Initial import of WAVE_ROVER_V1.0
This commit is contained in:
Joshua Sacherer
+575
@@ -0,0 +1,575 @@
|
||||
#define FEEDBACK_BASE_INFO 1001
|
||||
#define FEEDBACK_IMU_DATA 1002
|
||||
// esp-now recv
|
||||
// {"T":1003,"mac":"FF:FF:FF:FF:FF:FF","megs":"hello!"}
|
||||
#define CMD_ESP_NOW_RECV 1003
|
||||
// esp-now send status
|
||||
// 0:failed 1:succeed 2:Error initializing ESP-NOW
|
||||
// 3:invalid MAC address format.
|
||||
// 4:Failed to add peer.
|
||||
// 5:add peer. 6:delete peer.
|
||||
// 7:error sending the data. 8:sent with success.
|
||||
// {"T":1004,"mac":"FF:FF:FF:FF:FF:FF","status":1,"megs":"xxx"}
|
||||
#define CMD_ESP_NOW_SEND 1004
|
||||
// bus servos error feedback
|
||||
// {"T":1005,"id":1,"status":1}
|
||||
#define CMD_BUS_SERVO_ERROR 1005
|
||||
|
||||
|
||||
|
||||
// ---===< EoAT type settings. >===---
|
||||
|
||||
// modeType 0: gripper
|
||||
// {"T":124,"mode":0}
|
||||
// modeType 1: wrist
|
||||
// {"T":124,"mode":1}
|
||||
#define CMD_EOAT_TYPE 124
|
||||
|
||||
// EoAT assemble.
|
||||
// mount position: 0 - edge
|
||||
// 1 - D-3.2
|
||||
// 2 - D-4.2
|
||||
// 3 - D-10.2
|
||||
// -------L3A-----------O==L2B===
|
||||
// | ^ ||
|
||||
// L3B | ||
|
||||
// | ELBOW_JOINT ||
|
||||
// pos->X--L4A---O L2A
|
||||
// | ||
|
||||
// | L4B ||
|
||||
// / | ||
|
||||
// PI X-EA-X SHOULDER_JOINT -> OO
|
||||
// \ | [||]
|
||||
// EB L1
|
||||
// | [||]
|
||||
// -------- BASE_JOINT -> XX
|
||||
// unit:mm
|
||||
// {"T":125,"pos":3,"ea":0,"eb":20}
|
||||
#define CMD_CONFIG_EOAT 125
|
||||
|
||||
|
||||
|
||||
// ---===< UGV ctrl. >===---
|
||||
// SPEED_INPUT
|
||||
// {"T":1,"L":0.5,"R":0.5}
|
||||
#define CMD_SPEED_CTRL 1
|
||||
|
||||
// {"T":11,"L":164,"R":164} (input PWM +-255)
|
||||
#define CMD_PWM_INPUT 11
|
||||
|
||||
// {"T":13,"X":0.1,"Z":0.3} (m/s,rad/s)(Not for the products without encoders)
|
||||
#define CMD_ROS_CTRL 13
|
||||
|
||||
// MOTOR PID & WINDUP LIMITS
|
||||
// {"T":2,"P":200,"I":2500,"D":0,"L":255}
|
||||
// {"T":2,"P":20,"I":2500,"D":0,"L":255}
|
||||
// {"T":222,"name":"mission_a","step":"{\"T\":104,\"x\":235,\"y\":0,\"z\":234,\"t\":3.14,\"spd\":0.25}"}
|
||||
// {"T":222,"name":"boot","step":"{\"T\":2,\"P\":20,\"I\":2500,\"D\":0,\"L\":255}"}
|
||||
#define CMD_SET_MOTOR_PID 2
|
||||
|
||||
// OLED INFO SET
|
||||
// {"T":3,"lineNum":0,"Text":"putYourTextHere"}
|
||||
#define CMD_OLED_CTRL 3
|
||||
|
||||
// OLED DEFAULT
|
||||
// {"T":-3}
|
||||
#define CMD_OLED_DEFAULT -3
|
||||
|
||||
// MODULE TYPE
|
||||
// 0: nothing
|
||||
// 1: RoArm-M2-S
|
||||
// 2: Gimbal
|
||||
// {"T":4,"cmd":0}
|
||||
#define CMD_MODULE_TYPE 4
|
||||
|
||||
|
||||
// {"T":126}
|
||||
#define CMD_GET_IMU_DATA 126
|
||||
|
||||
// the robot need to be put on a ground and kept still
|
||||
// getting the imu offset and set as default
|
||||
// this gonna take a while (5s)
|
||||
// {"T":127}
|
||||
#define CMD_CALI_IMU_STEP 127
|
||||
|
||||
// {"T":128}
|
||||
#define CMD_GET_IMU_OFFSET 128
|
||||
|
||||
// {"T":129,"x":-12,"y":0,"z":0}
|
||||
#define CMD_SET_IMU_OFFSET 129
|
||||
|
||||
// {"T":130}
|
||||
#define CMD_BASE_FEEDBACK 130
|
||||
|
||||
// off: {"T":131,"cmd":0} [default]
|
||||
// on: {"T":131,"cmd":1}
|
||||
#define CMD_BASE_FEEDBACK_FLOW 131
|
||||
|
||||
// set the extra delay time(ms) for feedback info
|
||||
// {"T":142,"cmd":0}
|
||||
#define CMD_FEEDBACK_FLOW_INTERVAL 142 // dev
|
||||
|
||||
// set the echo mode of recving new cmd.
|
||||
// 0: [default]off
|
||||
// 1: on
|
||||
// {"T":143,"cmd":0}
|
||||
#define CMD_UART_ECHO_MODE 143
|
||||
|
||||
|
||||
|
||||
// LIGHT/GIMBAL/MOVTION CTRL
|
||||
// {"T":132,"IO4":255,"IO5":255}
|
||||
#define CMD_LED_CTRL 132
|
||||
|
||||
// GIMBAL CTRL(SIMPLE)
|
||||
// {"T":133,"X":45,"Y":45,"SPD":0,"ACC":0}
|
||||
#define CMD_GIMBAL_CTRL_SIMPLE 133
|
||||
|
||||
// GIMBAL CTRL MOVE
|
||||
// {"T":134,"X":45,"Y":45,"SX":300,"SY":300}
|
||||
#define CMD_GIMBAL_CTRL_MOVE 134
|
||||
|
||||
// GIMBAL CTRL STOP
|
||||
// {"T":135}
|
||||
#define CMD_GIMBAL_CTRL_STOP 135
|
||||
|
||||
// CHANGE HEART BEAT DELAY
|
||||
// {"T":136,"cmd":3000}
|
||||
#define CMD_HEART_BEAT_SET 136
|
||||
|
||||
// GIMBAL STEADY
|
||||
// off: {"T":137,"s":0,"y":0}
|
||||
// on: {"T":137,"s":1,"y":0}
|
||||
#define CMD_GIMBAL_STEADY 137
|
||||
|
||||
// SET SPEED RATE
|
||||
// {"T":138,"L":1,"R":1}
|
||||
#define CMD_SET_SPD_RATE 138
|
||||
|
||||
// GET SPEED RATE
|
||||
// {"T":139}
|
||||
#define CMD_GET_SPD_RATE 139
|
||||
|
||||
// SAVE SPEED RATE
|
||||
// {"T":140}
|
||||
#define CMD_SAVE_SPD_RATE 140
|
||||
|
||||
// GIMBAL USER CTRL
|
||||
// {"T":141,"X":0,"Y":0,"SPD":300}
|
||||
// -1: decrease
|
||||
// 1: increase
|
||||
// 0: stop
|
||||
// 2,2: middle
|
||||
#define CMD_GIMBAL_USER_CTRL 141
|
||||
|
||||
|
||||
// ---===< Arm ctrl. >===---
|
||||
|
||||
// it moves to goal position directly.
|
||||
// without interpolation.
|
||||
// {"T":100}
|
||||
#define CMD_MOVE_INIT 100
|
||||
|
||||
// {"T":101,"joint":0,"rad":0,"spd":0,"acc":10}
|
||||
// joint: 1-BASE_JOINT + ->left
|
||||
// 2-SHOULDER_JOINT + ->down
|
||||
// 3-ELBOW_JOINT + ->down
|
||||
// 4-EOAT_JOINT + ->grab/down
|
||||
// spd: steps/s
|
||||
// acc: steps/s^2
|
||||
#define CMD_SINGLE_JOINT_CTRL 101
|
||||
|
||||
// {"T":102,"base":0,"shoulder":0,"elbow":1.57,"hand":1.57,"spd":0,"acc":10}
|
||||
// input the angle in rad(180°=3.1415926).
|
||||
#define CMD_JOINTS_RAD_CTRL 102
|
||||
|
||||
// {"T":103,"axis":2,"pos":0,"spd":0.25}
|
||||
// axis: 1-x: 235.11
|
||||
// 2-y: 0
|
||||
// 3-z: 234.79
|
||||
// 4-t: 1.57
|
||||
#define CMD_SINGLE_AXIS_CTRL 103
|
||||
|
||||
// // // // // // // // // // // // // // // // // // // // //
|
||||
// {"T":104,"x":235,"y":0,"z":234,"t":3.14,"spd":0.25} //
|
||||
#define CMD_XYZT_GOAL_CTRL 104 //
|
||||
// // // // // // // // // // // // // // // // // // // // //
|
||||
|
||||
// {"T":1041,"x":235,"y":0,"z":234,"t":3.14}
|
||||
#define CMD_XYZT_DIRECT_CTRL 1041
|
||||
|
||||
|
||||
// {"T":105}
|
||||
// x: real x position.
|
||||
// y: real y position.
|
||||
// z: real z position.
|
||||
// t: real grab/hand angle in rad.
|
||||
// torB: base joint torque.
|
||||
// torS: shoulder joint torque.
|
||||
// torE: elbow joint torque.
|
||||
#define CMD_SERVO_RAD_FEEDBACK 105
|
||||
|
||||
// release:
|
||||
// {"T":106,"cmd":1.57,"spd":0,"acc":0}
|
||||
// grab:
|
||||
// {"T":106,"cmd":3.14,"spd":0,"acc":0}
|
||||
// hand joint ctrl using angle in radius.
|
||||
// {"T":106,"cmd":4.0,"spd":0,"acc":0}
|
||||
#define CMD_EOAT_HAND_CTRL 106
|
||||
|
||||
// {"T":107,"tor":200}
|
||||
#define CMD_EOAT_GRAB_TORQUE 107
|
||||
|
||||
// {"T":108,"joint":3,"p":16,"i":0}
|
||||
// change the P&I of a joint.
|
||||
// BASE_JOINT - 1
|
||||
// SHOULDER_JOINT - 2
|
||||
// ELBOW_JOINT - 3
|
||||
// EOAT_JOINT - 4
|
||||
// default p:32[servo] 16[RoArm-M2]
|
||||
// i: 0[servo] 8[RoArm-M2 PID MODE ON]
|
||||
// d: not used by default
|
||||
#define CMD_SET_JOINT_PID 108
|
||||
|
||||
// {"T":109}
|
||||
// reset the PID.
|
||||
#define CMD_RESET_PID 109
|
||||
|
||||
// set a new x-axis.
|
||||
// {"T":110,"xAxisAngle":0}
|
||||
#define CMD_SET_NEW_X 110
|
||||
|
||||
// set delay time
|
||||
// {"T":111,"cmd":3000}
|
||||
#define CMD_DELAY_MILLIS 111
|
||||
|
||||
// dynamic external force adaptation.
|
||||
// mode: 0 - stop: reset every limit torque to 1000.
|
||||
// 1 - start: set the joint limit torque.
|
||||
// b, s, e, h = bassJoint, shoulderJoint, elbowJoint, handJoint
|
||||
// example:
|
||||
// starts. input the limit torque of every joint.
|
||||
// {"T":112,"mode":1,"b":60,"s":110,"e":50,"h":50}
|
||||
// stop
|
||||
// {"T":112,"mode":0,"b":1000,"s":1000,"e":1000,"h":1000}
|
||||
#define CMD_DYNAMIC_ADAPTATION 112
|
||||
|
||||
// switch-12V ctrl.(NOT FOR UVG)
|
||||
// pwm: -255 ~ 0(off) ~ +255
|
||||
// {"T":113,"pwm_a":-255,"pwm_b":-255}
|
||||
#define CMD_SWITCH_CTRL 113
|
||||
|
||||
// light ctrl.(NOT FOR UVG)
|
||||
// led: 0(off) - 255(max)
|
||||
// {"T":114,"led":255}
|
||||
#define CMD_LIGHT_CTRL 114
|
||||
|
||||
// switch off.
|
||||
// {"T":115}
|
||||
#define CMD_SWITCH_OFF 115
|
||||
|
||||
// ctrl a single joint abs angle in deg.
|
||||
// joint: 1-BASE_JOINT + ->left
|
||||
// 2-SHOULDER_JOINT + ->down
|
||||
// 3-ELBOW_JOINT + ->down
|
||||
// 4-EOAT_JOINT + ->grab/down
|
||||
// spd: speed, angle/s^2
|
||||
// acc: speed, angle/s^2 (max: 22.5)
|
||||
// {"T":121,"joint":1,"angle":0,"spd":10,"acc":10}
|
||||
#define CMD_SINGLE_JOINT_ANGLE 121
|
||||
|
||||
// ctrl all joints
|
||||
// b - BASE
|
||||
// s - SHOULDER
|
||||
// e - ELBOW
|
||||
// h - HAND
|
||||
// spd - angle/s
|
||||
// acc - angle/s^2 (max: 22.5)
|
||||
// {"T":122,"b":0,"s":0,"e":90,"h":180,"spd":10,"acc":10}
|
||||
#define CMD_JOINTS_ANGLE_CTRL 122
|
||||
|
||||
// constant ctrl
|
||||
// m: 0 - angle
|
||||
// 1 - xyzt
|
||||
// cmd: 0 - stop
|
||||
// 1 - increase
|
||||
// 2 - decrease
|
||||
// {"T":123,"m":0,"axis":0,"cmd":0,"spd":3}
|
||||
#define CMD_CONSTANT_CTRL 123
|
||||
|
||||
// 124/125...131
|
||||
|
||||
|
||||
// === === === MISSION CTRL & FILE CTRL === === ===
|
||||
|
||||
// scan files in flash.
|
||||
// {"T":200}
|
||||
#define CMD_SCAN_FILES 200
|
||||
|
||||
// create a new file and input the content.
|
||||
// {"T":201,"name":"file.txt","content":"inputContentHere."}
|
||||
#define CMD_CREATE_FILE 201
|
||||
|
||||
// get a file content.
|
||||
// {"T":202,"name":"file.txt"}
|
||||
#define CMD_READ_FILE 202
|
||||
|
||||
// remove a file in flash.
|
||||
// {"T":203,"name":"file.txt"}
|
||||
#define CMD_DELETE_FILE 203
|
||||
|
||||
// add a line at the end of a file.
|
||||
// {"T":204,"name":"file.txt","content":"inputContentHere."}
|
||||
#define CMD_APPEND_LINE 204
|
||||
|
||||
// insert a new line as lineNum.
|
||||
// {"T":205,"name":"file.txt","lineNum":3,"content":"content"}
|
||||
#define CMD_INSERT_LINE 205
|
||||
|
||||
// change a single line in the file.
|
||||
// {"T":206,"name":"file.txt","lineNum":3,"content":"Content"}
|
||||
#define CMD_REPLACE_LINE 206
|
||||
|
||||
// read a single line from file.
|
||||
// {"T":207,"name":"file.txt","lineNum":3}
|
||||
#define CMD_READ_LINE 207
|
||||
|
||||
// delete a single line from file.
|
||||
// {"T":208,"name":"file.txt","lineNum":3}
|
||||
#define CMD_DELETE_LINE 208
|
||||
|
||||
|
||||
// torque-lock ctrl.
|
||||
// off: {"T":210,"cmd":0}
|
||||
// on: {"T":210,"cmd":1}
|
||||
#define CMD_TORQUE_CTRL 210
|
||||
|
||||
|
||||
|
||||
// === === === mission & steps edit. === === ===
|
||||
|
||||
// create a mission in flash:
|
||||
// {"T":220,"name":"mission_a","intro":"test mission created in flash."}
|
||||
#define CMD_CREATE_MISSION 220
|
||||
|
||||
// input the mission name and get the total content.
|
||||
// {"T":221,"name":"mission_a"}
|
||||
#define CMD_MISSION_CONTENT 221
|
||||
|
||||
// {"T":144,"E":100,"Z":0,"R":0}
|
||||
#define CMD_ARM_CTRL_UI 144
|
||||
|
||||
|
||||
// append a new step at the end of the mission, using the step input.
|
||||
// {"T":222,"name":"mission_a","step":"{\"T\":104,\"x\":235,\"y\":0,\"z\":234,\"t\":3.14,\"spd\":0.25}"}
|
||||
#define CMD_APPEND_STEP_JSON 222
|
||||
|
||||
// append a new step at the end of the mission, using the feedback.
|
||||
// {"T":223,"name":"mission_a","spd":0.25}
|
||||
#define CMD_APPEND_STEP_FB 223
|
||||
|
||||
// append a new delay(ms) at the end of the mission.
|
||||
// {"T":224,"name":"mission_a","delay":3000}
|
||||
#define CMD_APPEND_DELAY 224
|
||||
|
||||
|
||||
|
||||
// insert a new step as the stepNum
|
||||
// using the json string input.
|
||||
// {"T":225,"name":"mission_a","stepNum":3,"step":"{\"T\":104,\"x\":235,\"y\":0,\"z\":234,\"t\":3.14,\"spd\":0.25}"}
|
||||
// {"T":225,"name":"mission_a","stepNum":3,"step":"{\"T\":114,\"led\":255}"}
|
||||
#define CMD_INSERT_STEP_JSON 225
|
||||
|
||||
// insert a new step as the stepNum
|
||||
// using the feedback.
|
||||
// {"T":226,"name":"mission_a","stepNum":3,"spd":0.25}
|
||||
#define CMD_INSERT_STEP_FB 226
|
||||
|
||||
// insert a new delay(ms) at the stepNum.
|
||||
// {"T":227,"stepNum":3,"delay":3000}
|
||||
#define CMD_INSERT_DELAY 227
|
||||
|
||||
|
||||
|
||||
// replace the cmd at stepNum
|
||||
// using json cmd input.
|
||||
// {"T":228,"name":"mission_a","stepNum":3,"step":"{\"T\":114,\"led\":255}"}
|
||||
#define CMD_REPLACE_STEP_JSON 228
|
||||
|
||||
// replace the cmd at stepNum
|
||||
// using feedback.
|
||||
// {"T":229,"name":"mission_a","stepNum":3,"spd":0.25}
|
||||
#define CMD_REPLACE_STEP_FB 229
|
||||
|
||||
// replace the cmd at stepNum with delay cmd.
|
||||
// {"T":230,"name":"mission_a","stepNum":3,"delay":3000}
|
||||
#define CMD_REPLACE_DELAY 230
|
||||
|
||||
|
||||
// delete a step
|
||||
// {"T":231,"name":"mission_a","stepNum":3}
|
||||
#define CMD_DELETE_STEP 231
|
||||
|
||||
|
||||
// input the mission name and a stepNum, it will move to the step.
|
||||
// {"T":241,"name":"mission_a","stepNum":3}
|
||||
#define CMD_MOVE_TO_STEP 241
|
||||
|
||||
// input the mission name and repeatTimes to play a mission.
|
||||
// if repeatTimes = -1, it will loop forever.
|
||||
// {"T":242,"name":"mission_a","times":3}
|
||||
#define CMD_MISSION_PLAY 242
|
||||
|
||||
|
||||
|
||||
// === === === ESP-NOW settings. === === ===
|
||||
|
||||
// note: wifi must be running under STA(AP+STA) mode.
|
||||
// it will be controled by broadcast mac address.
|
||||
// {"T":300,"mode":1} [default]
|
||||
// it won't be controled by broadcast mac address, and add one mac to whitelist.
|
||||
// if there is no leader you can just fill 00:00:00:00:00:00 in it.
|
||||
// {"T":300,"mode":0,"mac":"CC:DB:A7:5B:E4:1C"}
|
||||
#define CMD_BROADCAST_FOLLOWER 300
|
||||
|
||||
// set the mode of esp-now
|
||||
// espNowMode: 0 - none
|
||||
// 1 - flow-leader(group): sending cmds
|
||||
// 2 - flow-leader(single): sending cmds to a single follower
|
||||
// 3 - [default]follower: recv cmds
|
||||
// flow-leader - use cmd=0, ctrl servos in real time.
|
||||
// leader uses the servos feedback pos to ctrl followers.
|
||||
// {"T":301,"mode":3}
|
||||
#define CMD_ESP_NOW_CONFIG 301
|
||||
|
||||
// get this dev mac address.
|
||||
// {"T":302}
|
||||
#define CMD_GET_MAC_ADDRESS 302
|
||||
|
||||
// add a new follower mac address to peer.
|
||||
// {"T":303,"mac":"FF:FF:FF:FF:FF:FF"}
|
||||
// {"T":303,"mac":"CC:DB:A7:5B:E4:1C"}
|
||||
// {"T":303,"mac":"CC:DB:A7:5C:1C:40"}
|
||||
// {"T":303,"mac":"CC:DB:A7:5C:E5:FC"}
|
||||
#define CMD_ESP_NOW_ADD_FOLLOWER 303
|
||||
|
||||
// remove a follower from peer.
|
||||
// {"T":304,"mac":"FF:FF:FF:FF:FF:FF"}
|
||||
// {"T":304,"mac":"CC:DB:A7:5B:E4:1C"}
|
||||
// {"T":304,"mac":"CC:DB:A7:5C:1C:40"}
|
||||
// {"T":304,"mac":"CC:DB:A7:5C:E5:FC"}
|
||||
#define CMD_ESP_NOW_REMOVE_FOLLOWER 304
|
||||
|
||||
// send info to more than one peer devs.
|
||||
// "FF:FF:FF:FF:FF:FF" can't be in the broadcast peer.
|
||||
// {"T":305,"dev":0,"b":0,"s":0,"e":1.57,"h":1.57,"cmd":0,"megs":"hello!"}
|
||||
#define CMD_ESP_NOW_GROUP_CTRL 305
|
||||
|
||||
// send info to a single dev, or to every devs by using "FF:FF:FF:FF:FF:FF"
|
||||
// broadcast ctrl:
|
||||
// {"T":306,"mac":"FF:FF:FF:FF:FF:FF","dev":0,"b":0,"s":0,"e":1.57,"h":1.57,"cmd":0,"megs":"hello!"}
|
||||
// {"T":306,"mac":"FF:FF:FF:FF:FF:FF","dev":0,"b":0,"s":0,"e":0,"h":0,"cmd":1,"megs":"{\"T\":114,\"led\":255}"}
|
||||
// single ctrl:
|
||||
// {"T":306,"mac":"CC:DB:A7:5C:E5:FC","dev":0,"b":0,"s":0,"e":1.57,"h":1.57,"cmd":0,"megs":"hello!"}
|
||||
#define CMD_ESP_NOW_SINGLE 306
|
||||
|
||||
|
||||
|
||||
// === === === wifi settings. === === ===
|
||||
|
||||
// config the wifi mode on boot.
|
||||
// 0 - off
|
||||
// 1 - ap
|
||||
// 2 - sta
|
||||
// 3 - ap+sta
|
||||
// {"T":401,"cmd":3}
|
||||
#define CMD_WIFI_ON_BOOT 401
|
||||
|
||||
// config ap mode.
|
||||
// {"T":402,"ssid":"UGV","password":"12345678"}
|
||||
#define CMD_SET_AP 402
|
||||
|
||||
// config sta mode.
|
||||
// {"T":403,"ssid":"na","password":"ps"}
|
||||
#define CMD_SET_STA 403
|
||||
|
||||
// config ap/sta mode.
|
||||
// {"T":404,"ap_ssid":"UGV","ap_password":"12345678","sta_ssid":"na","sta_password":"ps"}
|
||||
#define CMD_WIFI_APSTA 404
|
||||
|
||||
// get wifi info.
|
||||
// {"T":405}
|
||||
#define CMD_WIFI_INFO 405
|
||||
|
||||
// create a wifiConfig.json file
|
||||
// from the args already be using.
|
||||
// {"T":406}
|
||||
#define CMD_WIFI_CONFIG_CREATE_BY_STATUS 406
|
||||
|
||||
// create a wifiConfig.json file
|
||||
// from the args input.
|
||||
// {"T":407,"mode":3,"ap_ssid":"UGV","ap_password":"12345678","sta_ssid":"na","sta_password":"ps"}
|
||||
#define CMD_WIFI_CONFIG_CREATE_BY_INPUT 407
|
||||
|
||||
// disconnect wifi.
|
||||
// {"T":408}
|
||||
#define CMD_WIFI_STOP 408
|
||||
|
||||
|
||||
|
||||
// === === === servo settings. === === ===
|
||||
|
||||
// change a servo's ID.
|
||||
// {"T":501,"raw":1,"new":11}
|
||||
#define CMD_SET_SERVO_ID 501
|
||||
|
||||
// set the current position as the middle position.
|
||||
// > BASE_SERVO_ID 11
|
||||
// > SHOULDER_DRIVING_SERVO_ID 12
|
||||
// > SHOULDER_DRIVEN_SERVO_ID 13
|
||||
// > ELBOW_SERVO_ID 14
|
||||
// > GRIPPER_SERVO_ID 15
|
||||
// {"T":502,"id":11}
|
||||
#define CMD_SET_MIDDLE 502
|
||||
|
||||
// set the P/PID of a single servo.
|
||||
// {"T":503,"id":14,"p":16}
|
||||
#define CMD_SET_SERVO_PID 503
|
||||
|
||||
|
||||
|
||||
// === === === esp32 settings. === === ===
|
||||
|
||||
// esp-32 ctrl.
|
||||
// reboot device.
|
||||
// {"T":600}
|
||||
#define CMD_REBOOT 600
|
||||
|
||||
// get the size of free flash space
|
||||
// {"T":601}
|
||||
#define CMD_FREE_FLASH_SPACE 601
|
||||
|
||||
// boot mission info.
|
||||
// {"T":602}
|
||||
#define CMD_BOOT_MISSION_INFO 602
|
||||
|
||||
// reset boot mission.
|
||||
// {"T":603}
|
||||
#define CMD_RESET_BOOT_MISSION 603
|
||||
|
||||
// if there is something wrong with wifi funcs, clear the nvs.
|
||||
// {"T":604}
|
||||
#define CMD_NVS_CLEAR 604
|
||||
|
||||
// 2: flow feedback.
|
||||
// 1: [default]print debug info in serial.
|
||||
// 0: don't print debug info in serial.
|
||||
// {"T":605,"cmd":1}
|
||||
#define CMD_INFO_PRINT 605
|
||||
|
||||
|
||||
|
||||
// === === === mainType & moduleType settings. === === ===
|
||||
// {"T":900,"main":1,"module":0}
|
||||
// main_type: 1-WAVE ROVER, 2-UGV02, 3-UGV01
|
||||
#define CMD_MM_TYPE_SET 900
|
||||
Reference in New Issue
Block a user